Living In Your RV In The Winter Tips

We have talked about staying warm in your RV during the cold winter months. First by moving South to warmer weather but, for many that is not an option. If you have to say in the cold for whatever reason what should you do to help your RV not to freeze? Let's look at the different areas of the RV and what can be done to keep that area from freezing.






First the outside perimeter.  Ok, let's get it on the table, do not use bales of hay to surround the rig.

Why there are cheap and easy to stack?
Because of  FIRE, rodents, and bugs. If for some unknown reason the hay should catch fire there would be little chance of survival.  And don't forget that many outdoor creatures would love to come inside your RV and spend the cold winter months.

What can be used?  You can use skirting for your specific RV. Which is shown below;

Custom Trailer Skirting

While this is expensive it is a good solution to the problem of cold air getting under your RV.
Click on the link below the above picture or on the following link for details. EZSnapDirect.com

There is another solution for the DIYer and that is 

Rigid-Foam-Insulation-Board

Foil-Faced Foam Sheathing board is a rigid polyisocyanurate foam sheathing that provides exceptional heat, moisture, and air control.

• 4'x8' sheet (9' and 10' available via special order)
• 3/4" thick
• R-4.4
• One side has a reflective foil face typically installed toward the warm air surface to reflect energy back toward the dwelling and the other side has a white non-reflective foil face typically installed toward the exterior.
• Can be used in residential construction as insulated sheathing in above grade exterior walls, above and below grade interior walls crawl spaces attic, sand cathedral ceilings as well as Type I-V commercial applications
• Highest R-value per inch of any rigid board insulation.
• Does not melt when exposed to flame versus other types of rigid foam board (ASTM E84)
• Reflective aluminum foil face blocks radiant heat and prevents penetration of air and intrusion of moisture

Dimensions: 3/4" x 4ft x 8ft Cost as little as $9.25 per sheet

This type of foil backed foam board can be cut to fit and close-in around the RV to protect the underbelly of the RV from freezing. This type of insulation is available at Home Depot, Lowes, Menards, etc.

You would secure the foam to the RV and to itself by using aluminum heating duct tape.

Aluminum Heating Duct Tape

The area under the RV that you create by enclosing the area needs to be heated with a low heat generator such as this mini heater.

Mini Heater

This heater uses about 200 watts of AC power and I would use two of them for a 40ft trailer.  The heater should be placed off the ground several inches in case of water flow.

Second is the water and control compartment.

Yours may look different,  but the issue is that it needs heat.  This area should be kept warm by a Mini Heater or 60 watt light bulb.  The concern is the water hookup to the trailer and the ability to release the black and grey water tanks valves.  One problem you can encounter with a light bulb as a heat source is light.  In many articles that I have read on winter camping one solution to heating, a small area is using a 60 watt light bulb.  But at no time does anyone offer a solution to the light pollution that is given off by the bulb.  Here is one solution you might consider,  a

60 Watt Non-Lighting Heat Source

60 Watt Non-Lighting Heat Source

 This non-lighting heat source can be used by screwing into a clamp on-light fixture or using just a bulb socket and cord.

Following is a sample of a clamp on a lamp base.

Clamp On Lamp Base

For the fresh water lines, you will need to use the shortest hose you can to go between your rig and the fresh water source. 

Pirit Heated Water Hose

• Provides a constant source of water in freezing temperatures
• Thermostatically controlled
• Turns on when temperatures are below 45 degrees
• Turns off when temperatures are above 50 degrees
• Made from drink-safe PVC
• Keeps water from freezing down to minus 42-Degrees Fahrenheit
• Tougher thermostat

Do not let the hose lay on the ground.  You can do this by wrapping the water hose in pipe insulation. You can get some from Home Depot, Lowes Menards etc.

Pipe Insulation

Use some of the Aluminum Tape to seal the pipe insulation and do not forget to wrap the water source with pipe insulation to help keep it flowing.  Some people even build a box out of the foil foam board to cover the water source to further insulate.

Next the sewer and sewer hose. "DO NOT LEAVE THE DRAIN VALVES OPEN" Open as needed to dump the gray or black tank.  Use the shortest sewer pipe you can and you need to support it off the ground.  Wrap the sewer hose with heat tape first.

Heat Tape 30 Feet

Next wrap the sewer hose and heat tape in a blanket made from a Hot Water Heater Insulation blanket

Water Heater Insulation 

You want to wrap it tight and then tape it very well to hold it together.  Leave an overlap at both ends to go over the sewer connection and the sewer pipe that comes out of the ground and be sure the heater tape is wrapped around the end of the pipe that is attached to the RV as well as the water heater insulation blanket.

To keep the sewer hose off the ground and well supported you can use rain gutter pipe or you can use,

 RV Sewer Hose Support

Some RVers even put a gallon of RV antifreeze down the black tank after dumping the tank to help ensure that nothing gets frozen between dumps.

RV Antifreeze

I have not tried this myself, but there is no reason it would not be a good idea.  It is an added expense that would need to be considered.

I believe that covers the outside of the rig now let's move inside and see what can be done to keep out the cold and keep in the warm.

You need to check all the doors that you go in and out of the rig with.  If you can see daylight around the edge of the door with the door closed. You will have cold air coming into the rig.  You need to put door weather seal around the door to seal the door better.

Door Weather Seal

What about the windows you say.  You are right if your rig windows are single pane, as most of them are, you will need to winterize them as well.  The easiest way is to use the small bubble pack wrapping material that you can find almost anywhere.

Bubble Wrap

Installation
• Cut the bubble wrap to the size of the window pane with scissors.
• Spray a film of water on the window using a spray bottle.
• Spray a film of water on the bubble side of the bubble wrap using a spray bottle.
• Apply the bubble wrap while the window is still wet and press it into place.
• The bubble side goes toward the glass.
• To remove the bubble wrap, just pull it off starting from a corner.

Next, let's look at the vents in the rig. All of the vents through the roof allow warm air to rise into a cold space and chill the air.  We need to block the upward movement of the air but still be able to use the vent when needed.  A vent pillow is just the thing.  You can make them if you are handy or buy some cheap pillows you can stuff into the vent opening or you can get these.

RV Vent Insulator

Fits standard 14" RV vents

Reflective surface blocks the sun's damaging rays

Full 2.75" of foam to help stop heat transfer

Durable and easy to store

Keep your RV cooler in the Summer and warmer in the Winter

Now that we have sealed the rig against the cold air we have now trapped water vapor from cooking, propane heating, showers, and human breathing inside the rig.  You will begin to see water or moisture on the walls of the rig and anything that is colder than the inside air.  This is not good and can cause mold.  To get rid of the moisture and reduce the humidity we need a dehumidifier.  Several ideas come to mind.

First,

RV Dehumidifier

Quiet Small-Size Dehumidifier with No Moving Parts

Removable 16-oz. Water Tank & Washable Air Filter

Features 'Tank Full' Indicator Light

Auto-Shuts When Water Reservoir is Full

Measures Just 5.75" x 5.32" x 8.78" in

You might need two of these in a large 40ft rig.  They do work and keep the air drier but not completely dry.

Next is the Goldenrod Heaters.  You also will need several of these in larger rigs but they are smaller and you do not need to dump them, like the one above.

 Goldenrod Dehumidifier

This unit comes in different sizes up to 36 inches in length.  It consumes about 1 watt per inch and is mounted along the wall at the floor level.  You will need several in a large rig as they can dehumidify approximately 200 cubic feet of air. So if you have a bunkhouse then that room would have its own unit. The main living area would have one and the master bedroom would have one.

Something I have used is DampRid in closets and drawers where moisture is not wanted and may be harmful to the contents of the surrounding area.

DampRid Moisture Absorber

That should do it.  You have done your best to get the rig ready for winter and now the daily grind begins.  In a separate blog post, we cover how to keep you and the kids warm when it is cold outside.

Until next time.

And finally, please remember that this blog is an Amazon affiliate. When you order something through any of the Amazon links, it doesn’t add anything to your cost, but I do earn a small commission on everything you buy. Just click on an Amazon link, then shop as usual.

Can You Hear Me Now? Breaker Breaker 1..9.....

For this post, I would like to discuss keeping in touch with the family while camping.  Many people in the good old days, used string and two soup cans or a CB walkie-talkie to keep in touch with family members during camping.  Most of the campers in the olden time and even RVers today, nothing was or is used to stay in touch.  While some may believe that a cell phone is good enough, and it may be traveling down the interstate, in a campground in the wilderness or at the nearby lake you may find that the good old cell phone does not work, even a little.   You may find that the carrier you have is the wrong carrier for good service in the area that you are in and that the other guy would have been a better choice.  Whatever the case, today we have very small radios called FRS/GMRS that will last a long time on batteries, give you several miles of range, be quiet and can even be set up for "selective call" so only your family members will hear you when you call them in for lunch or are backing up the rig.  RVers who are backpackers take note, these little radios can have weather radios and GPS built-in as well.








Let's take a look at a few [shown below] and discuss their features and benefits in more detail.

Motorola Model MD200R

Shown above are some Basic FRS radios.  They come as a pair when you buy them and have the following feature set.  The units come with rechargeable batteries, two belt clips, charging cable, AC adapter and have a range of 20 miles over flat and open terrain.  They offer a 12hr battery life.  As you can see the unit does not offer a lot of features but it works and could be used when backing the RV into that tight site, right next to the lake.



Motorola MH230

Above is shown a step-up model of an FRS/GMRS radio.  It can run on alkaline batteries for up to 10hrs or 8hrs on rechargeable batteries.  This model from Motorola includes 11 weather channels, 22 talk channels, and each channel has 121 privacy codes, (selective call)  for privacy.  The range is 23 miles over flat and open terrain.  It comes with belt clips and 1 dual drop-in charger to charge the pair of radios at the same time to save you time.  Use one as a base station at the RV and give the other one to whoever you want to keep track of.  Additional units can be purchased so everyone who needs one has one.  This unit would be great for a fisherman to keep in touch while out in the boat on the lake.

Garmin Rino 650 with GPS & FRS



 Calling all Backpacking RVers out there.  Here is an FRS/GMRS radio that has a built-in GPS or a GPS that has a built-in FRS/GMRS radio.  This unit is not low cost, but it does show that just about any need for communications while RVing can be met with an FRS/GMRS radio.  For the fun of it here are some of the features of this radio.  The radio has a 2.6-inch color touchscreen that is glove friendly.  A high sensitivity GPS receiver, a rugged waterproof case. Runs 18hrs on a set of batteries, and has a list of accessories as long as your arm. 

While most of us will want a lower cost unit you need not suffer from little to no features.  Range, the number of channels, the privacy feature (selective call), and battery life are the important ones to watch out for.

Safety and peace of mind make the weekend RV getaway fun and exciting for the whole family and the ability to stay in touch with all members of the camping party does that for me and my family.









Until next time.  Over and Out?

Pressure And More Pressure On Your RV's Water Lines

Are you putting to much water pressure on your RV's PEX water lines and their PEX fittings?  Do you know how much pressure you can put on your RV's water lines and their  PEX fittings?
Let's take a look and see what's what.








RV manufacturers typically use PEX  PlasticTubing for all RV plumbing runs. The two sizes are commonly used, 3/8-inch and 1/2-inch. These are the standard size because the outside diameter of the tubing is about 1/8-inch greater than the called-for size. Red PEX is usually the Hot water line and Blue or Clear the cold water line.  But, not always.  There are special fittings used with this type of water line called PEX fittings.  Below are some examples of some fittings you might see under one of your sinks.

The fittings can be of any color or even colorless but they will all have the ribs you see on the fittings above.  You will also note that each PEX fitting has a crimped ring around it.  The ring looks like below.

To put the ring on the PEX tubing and secure the ring you would need a crimping tool.  Shown below.

OK, now that you understand what you currently have let's discuss the problems this type of system brings the RVer.  The whole system can leak at any time and usually does. Every connection, if it is not put on correctly, will leak at the worse possible time. Ah, you say no problem I will just squeeze the ring with my trusty pliers.  Well, your trusty pliers will not be able to squeeze the connector hard enough to seal the leak in most cases.  What to do?  Change the fitting to a more updated connector.  We will cover that in just a minute.

Why do these cheap PEX products not work well all the time?  PRESSURE, water pressure from campgrounds varies greatly and can not.  The PEX water system in an RV cannot safely go above 65 pounds of water pressure.  I will not allow mine to go over 55 pounds of pressure.  

How do I control the RV Parks water pressure with a brass water pressure regulator? 

Brass RV Water Regulator

 You can adjust this type of regulator to any safe water pressure you like for your RV.  This type of regulator does not affect the flow of the water just the pressure. There are lesser expensive water pressure regulators like the one shown below.

Fixed Water Pressure Regulator

While this type will regulate the water pressure it also affects the flow of the water which some people find objectable.  Either one will protect your RV water system from to much PRESSURE.

OK, you just found a PEX fitting under the kitchen island that is leaking now what can you do to fix the problem and how much time is it going to cost you?

You should carry a few Shark Bite connectors like the ones shown below.

Shark Bite Coupler

Shark Bite T

Shark Bite to Threaded 

There are even more fittings to choose from but you get the idea.  The advantages of these types of connector are, 

• INSTALLS IN SECONDS: 1/2 inch straight coupling requires no special tools, no soldering, no crimping or glue. Just push to create a watertight seal

• COPPER, PEX, CPVC: SharkBite straight coupling plumbing fittings fits copper tubing, and CTS CPVC and PEX and connects all three types in any combination

• CERTIFIED: SharkBite fittings are certified to 200 PSI and 200°F and can be reused up to four times

Now doesn't that beat the PEX connector and all the fuss it would take to fix a leaky connection?

The real story here is to control your water pressure coming into your RV.  If you do not you will find leaks and under the shower or under sink water damage.  

One other thing you may want to add a water shutoff to your toilet so in case you need to work on it you do not have to shut off all the water to the RV.

Shark Bite Shut Off

Until Next Time

And finally, please remember that this blog is an Amazon affiliate. When you order something through any of the Amazon links, it doesn’t add anything to your cost, but I do earn a small commission on everything you buy. 

Just click on an Amazon link, then shop as usual.

Propane Gas Saving Tips

I am sure most of you have noticed that gas of all kinds including diesel fuel is going up in price.  Many of us would like to stretch our Propane Gas as far as possible.  Well, there are some basic tricks of the RV lifestyle that can help you do just that.  You must have access to AC power (shore power) to make these tricks work.

The first one has to do with your hot water heater.  If your unit is a dual operating type (AC and Propane) force your unit to use AC whenever possible by shutting off your propane tanks. Turn your hot water heater off overnight.  The tank will keep the water hot to warm all night.

But your comment is, how will I cook anything?  The answer to that follows.

Second is to use induction cooking.  An induction cooktop uses magnetic energy to heat and cook whatever is in a pot or pan that a magnet can stick to.  For example, this Deluxe Burton Induction Cooktop is what I have and it works just great.  This is what it looks like;

Deluxe Burton Induction Cooktop

Here are some of the features of this Induction Cooktop ;

• 1800-watt high-quality induction cooktop provides 10 power levels
• Push-button controls and digital display; 180-minute timer with auto shut-off
• 10 temperature settings; overheat sensor; in-line fuse
• For use with induction-compatible cookware; the unsuitable-cookware detector
• Measures 13-2/7 by 12-1/2 by 2-3/5 inches

As mentioned in the features of the cooktop you must use cookware that a magnet will stick to.  Most cookware today is aluminum and so would not work.  You do not need a completely new set of cookware just enough to get by with using the induction cooktop.

Here is an example of Induction Cookware shown below;

Induction Cookware 

Any cookware will work as long as a refrigerator magnet will stick to the bottom of the pan or pot.  Here is a chance to go to Goodwill or other secondhand shop and make a killing on induction ready cookware.  Just be sure to bring your refrigerator magnet with you.

But you are a baker by trade and need to often use the oven that came with your Rig for that purpose.  What are you to do?  Well let's look at a solution called the Infrared Countertop Oven shown below;

Infrared Countertop Oven

Some of the features of this innovative oven are shown below;

• Digital-controlled infrared oven cooks food quickly and easily
• Cooking methods include conduction, convection, and infrared radiant heat
• No preheating, defrosting, or ventilation needed; dishwasher-safe parts
• Extender ring, cooking rack, baking pan, manual, and recipes included
• Measures approximately 14 by 14 by 16 inches
• 3-inch Extender Ring, 2-inch rack, 10-inch baking pan 
• Cooks up to a 16 Lb. turkey /141b ham with Extender Ring

So now we have the baking taken care of and we are not cooking with gas but electricity and so are saving gas and bucks ($). 

I heard you lady in the back row.  You are cold at night and need some heat so turning off the Propane gas is not an option.  Let's look at some options here as well.  

You could put one of these Mattress Heating Pads on your bed and plug into electric and sleep warm as toast all night.  These heated pads come in all the popular sizes King, Queen, and Twin.  I have shown the queen size below;

Mattress Heating Pads

Because heat rises this mattress type heating pad is much better than a heating blanket and will use less power to keep you toasty warm during the cold night. 

Ah, but you need to heat the Rig so you need more power, I mean heat.  Then you want a Ceramic Space Heater  This type of heater generates a lot of heat for very little electricity used.  The one pictured below is what I use.  I have a 30ft TT and use two of the Ceramic Heaters. One blowing toward the bedroom and one in the living room blowing toward the kitchen.  These heaters will cook you out of the Rig, they can generate so much heat.  I winter camp in North Texas and it can get below freezing, as we all found out in the winter of 2013/2014.  But even though my water hose froze outside, inside we were as warm as toast.  Shown below is the  Space Heater I have;

 Space Heater 

I have listed some of the features of this unit below;

• Ceramic space heater with adjustable thermostat for comfortable warmth—ideal for home or office
• 1500-watt high setting; 3 output options: Low, High, or Fan Only; power indicator light lets you know when it’s plugged in
• For safety: tip-over switch with auto shut-off and overheat protection with auto shut-off; ETL listed
• Carrying handle for easy transport; not for use in bathrooms, laundry areas, or other high-humidity rooms

If you have a four-legged friend (Furkid) traveling with you, please take note: this unit comes with Auto Shut-Off.  If the Ceramic Heater is tipped over the heater shuts off automatically.  This is a very important feature if you are traveling with four-footed friends.  There are some clumsy two-legged friends out there as well.

Again I remind you that these LP Gas saving tips only work if you have access to a power pedestal so you can get AC power.  With these hints, the Propane Gas becomes the backup plan and not the main source of energy for your Rig.  I know from experience that these hints and tips will work.

Until next time.

And finally, please remember that this blog is an Amazon affiliate. When you order something through any of the Amazon links, it doesn’t add anything to your cost, but I do earn a small commission on everything you buy. 

Water Out Of The Campground Faucet, YUCK!!

Well,  I suppose that most of you enjoy Artesian spring water with just a touch of Evian for good taste at your campground.  I know I do. NOT!!  While most city water is ok (well some is less than ok but just barely drinkable). Most campground water is not even ok but is drinkable.  With just a little bit of  DIY skills, you can improve your drinking, cooking, and shower water to be something to be proud of.  Enter the RV water filtration system.






Let's look at the simplest of these non-RV filtration systems and see what makes it filter.  The carbon/charcoal filter is the simplest of the non-RV water filters.  The filter holder can look like this

Culligan HF-150A Filter Holder

So how do you hook this blue thingy up to your RV?  You will need a few more simple parts.  The input and out put of the holder is 3/4" so any big box DIY store will have the needed plumbing parts.

You will need 3/4" Garden Hose to 3/4" Brass Coupler/Adapter  it looks like this

3/4" Garden Hose to 3/4" Brass Coupler/Adapter

This screws into the filter holder and allows the drinking water hose to hookup to it. (this attaches to the output of the filter holder)

For the input of the filter you will need a Female hose to Male pipe  It will look like the following.

Female hose to Male pipe 

You can mount the filter holder to the rig or you can just set it on the ground.  If you want to mount it you will need a Filter Mounting Bracket The filter mounting bracket will look like this.

Filter Mounting Bracket

You can use the bracket if you wish or just sit the filter canister on the ground.  Next, comes the Drinking Water Filter with Carbon  The filter comes in a two pack and looks like below.

 Drinking Water Filter with Carbon

So you are saying to yourself  why do I want to DIY this type of project when I can just go and buy one of these,

RV Water Filter

The answer is, that once the big blue filter is put together, you can get two of the filter replacement cartridges for big blue for less than one of the above filters.  Also, there is the chance of bacterial build up because, unless you are a full timer you are not using the filter enough.  With the replacement cartridges, you can just take it out and throw it away and use a new one next time you go out and you will still be saving money.

But wait there is more.

What if we add a second big blue filter?  Would we gain anything?  You bet.  So let's do it.

The two stage filter

For a two stage filter, you will need everything we listed for the one stage filter plus a 3/4" Brass Nipple that looks like this,

3/4" Brass Nipple - Length you must determine

You will need to measure the length that the nipple must be and buy one from one of the Big Box DIY stores. This nipple will be used between the blue filter cans and the other fittings will be the input and the output of the filters just as before.  You now have a chance to increase the filtering of your drinking water.  Now you will start to use Sediment Replacement Filter which looks like this,

Sediment Replacement Filter

A sediment filter gets rid of: sand, silt, dirt, rust particles and scale particles The park water should come into this filter first, then go through the Drinking Water Filter with Carbon and finally into your rig.  So now we are done, right?  Not so fast RVer slow down and keep reading.

The Triple RV Filter

With this type of filter system, you have the best possible filter system for still not a lot of money.  So what do you need?  Everything listed above plus an additional 3/4" Brass Nipple of the correct length to go between two more blue filter canisters.  Plus one more special type sediment filter the Special RV Filter which looks like this,

Special RV Filter

This special filter goes just before the Drinking Water Filter.  I know this looks like a lot of work but it really is not.  It is just a lot of hooking up of pipes to plastic.  You will need some Plumbers White Tape which looks like this,

Plumbers White Tape 

I would suggest getting several rolls as the tape tends to tangle and get wasted.  You will want to check for leaks after assembly by hooking up your filter system and be sure to let the water from the filter system to run on the ground for five minutes or until the water is running clear.  Some black pieces of carbon may come out onto the ground and this is normal.

Mounting the filters

You can use a 2"X 4" (2x4) of the length you need and mount the filter holders to that as a way of keeping them corralled together or you could mount them in one of the service bays on the rig. It is up to you.
The water you will get from the triple filter has to be drunk to be believed.  This system will not take pond water or salt water and make it drinkable.  This will, however, make city treated or treated well water taste just great.  And the wife's ice tea will be out of this world.






Until next time


And finally, please remember that this blog is an Amazon affiliate. When you order something through any of the Amazon links, it doesn’t add anything to your cost, but I do earn a small commission on everything you buy. Just click on an Amazon link, then shop as usual.

Martha!!! The String On The Blind Broke Again!!!

It happens to most of us,  we grab the shade bar at the bottom of the window blind and pull down to get ready for bed and the darn string running through the blind breaks and while it will go down all the way, there is no possible way that it will go up and stay where you want it in the morning. RATS now what?

RV Window Shade

Above is your typical RV window shade and if you look close you can see the string running through the blind material.  I suppose you could buy a RV Blind String Repair Kit, shown below

RV Pleated Shade First Aid Kit

While the hours spent restringing the blind with your spouse may be enjoyable, you might want to consider the frustration of not getting it right even after the 5th attempt. 
My suggestion is to replace that blind with something that is a whole lot prettier and will class up the inside of your rig as simple as ABC.

There are two basic RV Blinds.  First the roller blind.  As the name implies it is on a roller and you pull it down to the level you want and the blind will stay there.  The roller blind comes with two blinds on the roller. One is the daytime shade and the other is the night time or black out shade.  The roller can be installed on the outside of the window frame or on the inside of the window frame and is offered in colors for the daytime and night time shade.

Roller Bind Shade

Measuring Instructions:
Determine if the shade will mount outside the window frame onto the wall (Outside mount) or if the shade will be mounted inside the window frame (Inside mount) 

NOTE: Most RV applications are Outside mount.

Outside mount: Measure the width (across) of the area to be covered.Example - Edge of the window to the edge of window plus 2" added for additional coverage.

Example: Top of the  frame to  the bottom of  the frame with an additional 2" added for mounting above and below  the window.(outside mount)

Inside Mount: Measure the exact opening size and subtract a half inch. Measure the length (Drop) of the area to be covered.

If draperies or valances are already installed be sure your measurement for width allows the shade to fit under the current window treatment.
You can see that you end up with two shades one for daytime and one for night time.  You may find that this is not really what you are looking for and would rather have a true Vinyl 1 Inch Mini Blind.

Vinyl ! inch mini Blind

Measuring Instructions:
Determine if the blind will mount outside the window frame onto the wall (outside mount) or if the blind will be mounted inside the window frame (inside mount)  

NOTE: Most RV applications are outside mount.

Outside mount: Measure the width (across) of the area to be covered.  
Example - Edge of  the window to the edge of window plus 2" added for additional coverage.

Example: Top of the frame to the bottom of  the frame with an additional 2" added for mounting above and below  the window.(outside mount)

Inside Mount: Measure the exact opening size and subtract a half inch. 
Measure the length (drop) of  the area to be covered.

If draperies or valances are already installed be sure your measurement for width allows the blind to fit under the current window treatment.

You can get wooden blinds or different color Vinyl blinds to match or enhance the inside appearance of your rig.  Metal blinds are not recommended because of moisture in the rig.  The edge of the blind tends to rust and the blinds are a bit sharp around kids and fur-babies.
Caution: if you remove blinds from your windows keep all screws that were used to be sure that you do not use a screw that is too long for your RV side walls.

Until next time.

The Open Range RV Owners is a Facebook Group on RVing with Hints & Tips. A group for the Full-timer as well as the Newbie. In case U can't find us "Facebook.com/groups/Open Range RV Owners" we are here hoping you will join us!

And finally, please remember that this blog is an Amazon affiliate. When you order something through any of the Amazon links, it doesn’t add anything to your cost, but I do earn a small commission on everything you buy. Just click on an Amazon link, then shop as usual.