Showing posts with label Cold Tires. Show all posts
Showing posts with label Cold Tires. Show all posts

Sunday, January 27, 2019

Do RVers Really Need A Power Management System?

I see that question all the time on Facebook and most of the Blogs that I read.  For the simple, easy, straightforward answer, YES you do.  There are so many factors involved here that I can not possibly cover them all in a single post but, I would like to cover the basics so that you can better understand why you need a Power Management system of some kind.





1. You need to know what the AC (Shore Power) voltage is inside your rig.  This is the power that indirectly powers lights, water heater, microwave, furnace, charger for the 12-volt battery system, etc.  If the voltage gets below 102 volts and should stay there for a few minutes it would be possible to sustain approximately $1200 of damage or more.

So what do you need?  You will need an AC Line Voltage Monitor.  The unit shown below is plugged into an AC wall outlet that you can see and will monitor what the line voltage is.  If it should go below 105 volts you need to unplug your rig from the outside power pedestal until the voltage goes back to normal.
AC Line Voltage Monitor
So how do you know when the outside power pedestal is back to normal.  You plug the Voltage Monitor into the 125 volts two pin socket in the power pedestal and see what the monitor reads.  It should read 110 volts or higher up to 125 volts.  The same caution goes for overvoltage.  You should unplug the rig from the power pedestal if your Voltage Monitor begins to read over 122 Volts.  Plug the Voltage Monitor into the power pedestal and watch for the voltage to drop to below 122 Volts.
Could this monitoring of the voltage be done for less money?  Yes, by using a cheap Digital Volt Meter  pictured below;
 Digital Volt Meter  

Harbor Freight often offers a cheap digital voltmeter for free, with coupon.  Watch their ads and take advantage of the offer.  You could plug the test leads that come with the meter into the meter and then the other ends of the test leads into the slots on the AC wall socket. (Caution do not leave unattended) Or you could make up a cord from a 6-foot extension cord and the test leads that come with the meter.  See below for an example.
AC Cord With Test Meter Leads

2. Next is  The Polarity Tester.  This is used to be sure that the Neutral wire of the power line is not reversed with the positive lead of the power line.  If that were to happen you could have what is called a hot-skin condition.  Meaning that if you had an aluminum skinned rig you could receive quite a shock from your rig.
 The Polarity Tester
The Polarity Tester can also tell you if the Earth Ground (the bare copper wire) is hooked up properly.  
The Earth Ground is a separate conductor which may seem to be doing nothing but, is, in fact, a protective wire. It is there, ready to take the current away to earth ground, from the body or frame of the electrical device it is connected to, makes contact with any "hot" wire. [the 120 volts mains power is carried in two current carrying conductors called "hot" and "neutral".] 
So, IF one of the "hot" conductors should contact the metal frame of the rig, or housing of an appliance, perhaps because the appliance got damaged by being dropped from a table, or similar accident,  the third wire which is the earth ground wire, which runs directly from the housing to the grounding [or earth ground bus] in the fuse or breaker panel, will in effect cause a short circuit which should blow the fuse or trip the breaker. 
This third wire also guarantees a current path back to the electrical panel where the fuse or circuit breaker protecting that circuit is located, in the event that the hot wire should come in contact with the rig's frame, but the neutral conductor should happen to have been cut or damage and become disconnected, or open. 
The idea is to guarantee that if a part of the rig, device or appliance should become "hot," which could be fatal to anyone who then came into contact with it. That the earth ground would trip/open the circuit protection device [fuse or breaker], and turn off the flow of AC current. 


To help further in checking for unwanted or wanted electricity a good investment is the, Voltage Sensor which is shown below;
 Voltage Sensor
With this probe, you do not need to touch the power line to tell if there is voltage present.  You can use this probe to find power lines behind the wall or under the floor of the Rig as well as the towing vehicle.

3.  Often times you want to know or need to know how much power something uses, especially if you keep popping a breaker or the power pedestal. The solution is Kill-A-Watt .  The unit shown below can be used to show how much power an appliance, tool or piece of electronics is using.
 Kill-A-Watt
4. Next, let's look at surge protectors for the various pieces of equipment in your Rig.  Surge Protectors protect only what is plugged into them and only for over-voltage surges.  Surge Protectors do not protect for under voltage or high voltages.  Shown below is a pair of good simple surge protectors;
Surge Protectors
There are Appliance Surge Protectors made just for appliances like microwave and coffee makers


AC refrigerators, freezers
Refrigerator/Freezer Surge Protector

These special surge protectors offer extra features like audible alarms, flashing lights, displays, etc and are to be used with just the items listed on the packaging for the one you would buy.

5.  Next is a group of power management items that will protect your entire Rig not just one item or several items in it. First is the Portable Power Management System This type of system looks at High and Low voltage protection, a time delay for air conditioning compressor startup, 3-mode surge protection, reverse polarity protection, open neutral protection, open ground protection, AC frequency protection accidental 220 Volt protection. Includes an Integrated information panel, previous error code display is weather resistant and has a built-in locking bracket so it can be chained to the power pedestal at the campground to prevent theft.  The only thing this unit cannot do is flush the black water tank.  The miracle unit we are talking about is shown below.



These portable units come in two sizes the one above 30 amp and the one shown below 50 amp.

Let's say you were involved in a lightning-caused power surge at a campground.  It is estimated you would suffer approximately $3000 to $5000 worth of damage to the electrical system of your Rig along with the things plugged into it.  The features of the 50 amp unit are the same as the 30 amp unit.
Ah, but there is more!  What happens if you do not want something portable but something more permanent in the Rig? Then you have the permanently installed units which are called Fixed Power Management Systems  These units are not really a DIY type of item but, they can be installed by the DIYer if care is taken during the installation.  The 30 amp model is shown below;
 30 Amp Fixed Power Management Systems
There is also a 50 amp version of the same unit as above and can be found here;  50 Amp Fixed Power Management Systems .  The features of both units are the same and are,  high and low voltage protection, time delay for air conditioning compressor start-up, 3 mode surge protection, surge trip indicator, reverse polarity protection, open neutral protection, open ground protection, AC frequency protection. Accidental 220V protection, with remote information display panel, and unit bypass switch.  Unfortunately, this unit also does not dump the black tank.

I hope that you now have come to the conclusion that some type of power management is needed to protect your Rig, its contents and YOU!









Until Next Time





And finally, please remember that this blog is an Amazon affiliate. When you order something through any of the Amazon links, it doesn’t add anything to your cost, but I do earn a small commission on everything you buy. Just click on an Amazon link, then shop as usual.

Monday, January 14, 2019

Improve Your Over The Air HD Reception

If you are RVing for just a weekend or full timing it, the chances are good that you will be within the range of one or more HD TV channels.  The problem is that most of us just can't seem to get enough signal to watch TV.  Heaven forbid that it rains and you would need something to entertain the kids besides a good book.






Most RVs come with a crank-up antenna like the following.
While this antenna is a good one, it was designed for mostly VHF analog TV reception.  (The old style TVs.)  Most of the TV reception today is UHF digital and calls for a bit more antenna.
Winegard has solved the problem with the addition of the Wingman below.



This unit attaches to your current Winegard crank-up antenna and really does boost HD TV reception.  No special tools are required to attach it to your current antenna.  Just follow the instructions that are included with the antenna.
I have added one of these Wingman Antennas to my crank-up RV antenna and have really seen a major improvement in the number of channels that I can receive as well as the strength of the signal on the channels that I could always get.

Let's talk about the maintenance of your crank-up antenna.  At least once an RV season you should get up on the roof of the RV and lubricate all the swivel points on the crank-up mechanism.  I have used  White Grease in the past but this year I am going with T9 Lube which is a bit less messy than the white grease.

Now that you have a great HD TV Antenna you might need some help pointing your TV antenna for better reception of local stations, try this link: Maximize your television reception.  Follow the instructions,  just enter the zip code where you are, or use the map to place a pin where you are and the site will tell you the best direction to get the strongest local TV signals. Be sure to tell the program that the antenna will be mounted more than 30ft in the air to get all the TV channels.  Along with a list of the TV stations within range.

Have you read stories about RVers forgetting to crank-down their TV antennas and losing them to a tree?  Here is an idea to stop that.

This kind of idea has worked for me.  You could use some brightly colored ribbon and just write Antenna on it and attach it to the crank handle of the antenna and put a second reminder in the towing vehicle.  Anything to remind you to crank the antenna down.

Also, do not forget to check the antenna amplifier switch is you are having problems with off the antenna reception.  When you switch from park satellite/cable you will need to turn the antenna amplifier back on.  Most RV parks request that you turn the antenna amplifier off when hooking up to the parks system.






Until Next Time.

Monday, November 12, 2018

RV Humidity -- An RV Rig Killer!

A strong title, but true.  One of the major killers of RV walls is moisture in the form of humidity.  You don't even have to be using your RV it can be sitting in storage and humidity can still be present on the inside above a safe level.  Mold depends on moisture to grow and flourish. What is a person to do?  Well, the safe level of humidity for an RV is 40% or thereabouts.  So the first thing you need to do is know your current humidity level and the best way to know that is with a humidity monitor.








In the photo for the Humidity Monitor, the screen is showing 53% which is not acceptable for an RV.  The reading shown is more likely a Sticks&Bricks house.
Now that you know what the humidity is.  What can or should you do if it is not right.  You need to try and find out the source of the moisture causing the high humidity.  People give off moisture when we breathe, but getting rid of all the kids is not an option be they fur or not.

Next showers or taking a bath gives off moisture.  Be sure that the bathroom fan is turned on during the bathing process, even in the colder months.  Wipe down the shower and bath area to reduce the amount of moisture that is evaporated back into the air of the RV.

Cooking is another moisture generator.  Keep lids on pans when cooking, to keep the moisture down, open a window a bit to let the warm moist air out, and turn on the kitchen vent if you have one.  Many of the newer RVs do not vent the stove vent to the outside.  This is not good, as an inside vented stove hood keeps the moist air inside the RV.  Do not let a tea kettle steam longer that is necessary.  Don't leave a coffee pot running all day long.  Make a cup as you need it or the coffee pot will add to the humidity in the RV all day long.

Try to locate any seals in the RV slides that is letting in outside air and seal that area.  You can cut strips of foam insulation like Reflectix or other foam insulation.  If you find caulking around the tub or shower stall or even around the kitchen/ bathroom sink is missing or cracking re-caulk using 100% silicone sealant like shown below.  This keeps water from going in the RV wood structure or supports where, if conditions are right, mold will start to grow.

If it is during the colder months and your RV has single pane windows you might add Bubble Wrap to the windows.
To install the bubble wrap do the following.

Cut the bubble wrap to the size of the window pane with scissors.
Spray a film of water on the window using a spray bottle.

Apply the bubble wrap while the window is still wet and press it into place.
The bubble side goes toward the glass.
To remove the bubble wrap, just pull it off starting from a corner.

This bubble wrap will help insulate the inside of the window from the outside of the window to further reduce moisture forming on the inside of the window when the outside air is colder than the inside air.

Do you dry clothes in the RV by hanging them in the bathroom?  Did you remember to turn on the exhaust fan?  It is not wise to dry clothes in the RV during the colder months because drying clothes adds to the amount of moisture inside the RV.  Do you have a combination washer/dryer?  Make sure the dryer is vented to the outside.  If you do not the dryer will add to the moisture in the RV.

If it possible let the RV inside temperature drop a bit in colder weather so the air inside the RV will hold less moisture.  Cooler air holds less moisture than warm air.  You may have to dress a bit warmer, but your RV investment will thank you for being a bit cooler.

Poor air circulation inside the RV can make mold grow in drawers, closets, and even cabinets.  Keep the air moving even when you are not inside your RV.  How may you ask? You can open two or more roof vents or a roof vent and crack a window so that air naturally flows in and out.  You can add a MaxxAir vent cover

over your current roof vents so that you can keep your vents open without rain or snow coming in the RV when the roof vent is open. You should put your RV in storage with vents cracked a little bit to allow for air movement.

If your RV does not have LED lighting you could swap out your current incandescent light bulbs for the LED equivalent.  This will reduce the about of air heating that the hotter incandescent bulbs are known for.  There is an LED replacement light for most all of the RV incandescent bulbs used in RVs. As an additional benefit, your RV battery will last longer during dry camping with LED lighting and depending on the LED light you buy you may find that the inside of your RV is now brighter with the lights on.

OK, we have talked about what not to do and some of what you can do to reduce moisture in the RV now let's get serious about stopping or greatly reducing moisture in your RV.
1. Get a dehumidifier.  They come in several sizes and types.
The ezest one to do business with is the bead type.

Twin Pack resealable packaging
100% silent operation
Lasts 45-60 Days
Indicator beads let you know when it's ready to be discarded.

You can spot these around the RV and in closets, cabinets, drawers where ever you feel or think moisture may be lurking.
Next, you have the mechanical dehumidifiers.

Whisper quiet
Renewable reservoir
Compact size is perfect for bathrooms, closets, and R.V.s
Low energy consumption
One of these usually works but if you have a severe problem you may want to consider two of them.

If you have an RV more than 36 feet long you may want to consider this one.

Squeezes Up to 20 oz. of Water a Day From Humid Air
Very Quiet Operation Due to No Moving Parts
At Capacity, Indicator Lights Up and Device Shuts Off
Compact at 4.45 pounds, 6.8" x 8.5" x 14"
For bunkhouse RVs,  you will need two.

And if you really need more moisture removal you can use a sticks and bricks type unit.
Removes up to 70 pints of moisture from the air per day
1.3-gallon water tank with transparent water level indicator, full bucket alert, and automatic shut-off when full
Removable, easy-cleaning dust filter with a clean filter alert
4 durable, rolling casters for easy movement

 It is generally felt that combinations of dry and mechanical work the best.

Well, that should about do it for this topic.  I hope you found the information helpful and can use some of the ideas presented.

Until Next Time







And finally, please remember that this blog is an Amazon affiliate. When you order something through any of the Amazon links, it doesn’t add anything to your cost, but I do earn a small commission on everything you buy. Just click on an Amazon link, then shop as usual.

Monday, October 29, 2018

How To Stay Warm Inside The RV When It Is Cold Outside

There is a group of us RVers that like to camp all year long and we live where that is possible.  Some of us Cold Weather RVers have little choice and must be in our RV all year long.  So how can you stay warm inside the RV when the world around you is just too cold?






Let's be clear on one point. If you have a rig that can take the cold it can only take it if the main furnace is set to keep the inside of the rig above freezing.  Most all weather rigs must have the furnace running to keep water pipes that run inside the rig from freezing.  That includes the black tank and grey water tanks as well. So you will need to keep the rig furnace going but you do not need it running at 72 degrees.

Let's talk about keeping you warm and comfortable.  I suppose we could all dress like Eskimos, but that seems a bit much for just reading a book inside our rig or maybe eating dinner.
You could wrap yourself in an electric throw blanket and be comfortable, like this one.

If you added these to your feet you would be warm as toast.

OR
These Footies or Snoozies and the electric throw you should be able to sit around and enjoy TV or read a good book.
But what about sleeping in bed?  That is a good question, so let's take a look at that.
You could put one of these Mattress Heating Pads on your bed and plug into electric and sleep warm as toast all night.  These heated pads come in all the popular sizes King, Queen, and Twin.  I have shown the queen size below;

Mattress Heating Pads
Because heat rises this mattress type heating pad is much better than a heating blanket and will use less power to keep you toasty warm during the cold night.  That might be good for the sleeping time but what about being up and moving around the rig?

Ah, but you need to heat the Rig so you need more power, I mean heat.  Then you want a Ceramic Space Heater  This type of heater generates a lot of heat for very little electricity used.  The one pictured below is what I use.  I use two of the Ceramic Heaters. One blowing toward the bedroom and one in the living room blowing toward the kitchen.  These heaters will cook you out of the Rig, they can generate so much heat.  I winter camp in North Texas and it can get below freezing, as we all found out in the winter of 2013/2014.  But even though my water hose froze outside, inside we were as warm as toast.  Shown below is the  Space Heater I have;


I have listed some of the features of this unit below:
  • Small Heater Measures: 6.2" X 4.74" x 8.3" . 
  • Three Modes Heater With Fan: 1.High Heat (1500-watt), 2. Low Heat(750-watt ), 3. Fan Only.
  • FOR SAFETY: 1.Automatic overheat system will shut the unit off when the parts of the heater overheat. 2. TIP-OVER SWITCH will shut off unite when tipped forward or backward.

    If you have a four-legged friend (Furkid) traveling with you, please take note: this unit comes with Auto Shut-Off.  If the Heater is tipped over the heater shuts off automatically.  This is a very important feature if you are traveling with four-footed friends.  There are some clumsy two-legged friends out there as well.

    There are other options to keep warm in the RV you could also use one or more of these oil filled heaters.

    The simple controls allow users to customize their heat with an adjustable thermostat and three temperature settings, and the ComforTemp setting maintains an optimal room temperature while conserving energy. The heater never requires refilling, and the anti-freeze technology automatically turns the unit on when the temperature drops below 42 degrees.
    Oil heaters are quiet and run about 10.5 cents an hour to operate which can be a money saver compared to other types of heaters. 

     I know from experience that these hints and tips will work. They keep the family warm during our cold weather camping, which we enjoy most of the time. 




    Until next time.

    And finally, please remember that this blog is an Amazon affiliate. When you order something through any of the Amazon links, it doesn’t add anything to your cost, but I do earn a small commission on everything you buy. 
    Just click on an Amazon link, then shop as usual.

    Saturday, September 22, 2018

    RV Security On The Road And In Storage

    It is that time of year again when most of us will have to store our RVs until next Spring. We all do the Winterizing like we are suppose to.  But how many of us even worry about someone coming along and stealing our RV?  Well, we should.  Let's take a look at what you can do to protect your, very expensive RV from being stolen.
    Because I live in the city, I can't store my Open Range 3X anywhere on my property or on the street. So like a lot of city dwellers I have to put my RV in storage when I am not using it.  To my shock and amazement, two units were stolen right out of the storage lot that I use.  To add insult to injury, the storage lot had a guard on site, a security system for entrance, and security cameras.  But the same guy managed to get two units out of the locked lot.  Well, thanks to the security cameras they caught the guy.  But what can you and I do to make our units harder to steal and more secure.  Let's look.





    First, we can add a lock to the ball area of a TT and a 5th Wheel Hitch Lock. Let's look at both.  The TT ball lock looks like below.


    • One size fits all (from 1-7/8", 2", to 2-5/15", all coupler types)
    • Keyhole cover slides up to seal out dirt and grime
    • Type A key which is a spring loaded, 7 pin, high-security key. Resists attempted drill outs. Rugged and durable, the key will not bend or break.
    • Huge 6 tooth, 3/8" dual ratchet locking system
    • Hardened 5/8" 16mm steel shackle

    Now that should slow down anyone trying to take the TT quickly.  Now let's look at what can be done to slow down the would-be thief stealing a 5er.  See below for the 5th Wheel Anti-Theft device

    5th Wheel Anti-Theft device
    This unit slides over the hitch pin and prevents the hitch pin from being attached to, by the hitch receiver. Simple but effective to slow down our would-be thief.

    I think we could do more. How about we lock the tires so the RV cannot be moved without putting new tires on the RV? Shown below is an RV Dual Wheel Stop with Padlock
     RV Dual Wheel Stop with Padlock

    • Secure tandem tires to prevent movement while parked or re-hitching
    • Fits 26" to 30" diameter tires with tire spacing of 3-1/2" to 5-1/2"
    • Includes, padlock
    • Easy grip handle for easy installation
    • Lightweight and durable

    This should slow them up but what about something even better?  Let's look at the X Wheel Stop with Padlock.
     X Wheel Stop with Padlock.

    While the lock for this heavy-duty unit is extra (a Master Lock, that you supply) it will be well worth it if it slows down someone trying to take your RV.  In most cases, if it is hard to take or time-consuming to take the thief will move on to easier pickings.

    We have protected (to the best of our ability) someone trying to take your RV but what about protecting the expensive stuff inside the RV and in the storage bay.  Let's take a look on how to help protect those areas.

    First the entrance doors.  Did you know that the key to your RV has been duplicated many times by the manufacturer of your RV?  Did you know that almost any thief can come up with a key that fits your RV doors?
    So let's look at a lock that is a bit safer. The Keyless RV Door Lock
    Keyless RV Door Lock

    • No wiring needed; uses 4 AA batteries (not included) It's retrofittable in most RV entry doors and it's easy to install.
    •  Programmable with a 4 digit PIN number The large buttons are easy to see and use Proximity sensing which illuminates the buttons.
    • Self-contained electronic RV latch with Capacitive Touch Technology
    • Offers hassle-free touchpad access: no key or fob to carry with you.
    • An integral touchpad to the latch which controls the deadbolt
    • Deadbolt key will always be able to operate the paddle or deadbolt lock in case of the user forgetting the code or having a dead battery, 8-inch x 5-inch x 4-inch.
    You don't even need a key to get this lock to open after you enter your personal pin number.  So it will not be a big deal if you lock your keys in the RV. By mistake, of course.

    Let's take a look at the outside storage compartment locks.  Did you know that's the lock code for your storage compartment lock is CH751?  This is the most common lock used on TT and 5th wheels today.  So anyone can get in. Let's look at a better idea. The RV Storage Compartment Combi Lock.

    RV Storage Compartment Combi Lock
    • Cylinder length 1-1/8"" - accommodates material thickness up to 7/8" thick
    • Durable solid metal
    • 1,000 possible combinations- set your own code
    • Retrofits any standard cam lock
    • Comes with 3/4" prong washer, 1-1/2" offset cam, 3/4" straight cam, 1-1/2" straight cam and a 90 degree stop.

    This type of lock is a direct replacement to what comes on most TTs and 5ers. You take off the old one and measure the hole opening and the length of the shaft and order the same size as the one you have.




    Follow the installation instructions and you are done. A really simple install.






    Until Next Time



    And finally, please remember that this blog is an Amazon affiliate. When you order something through any of the Amazon links, it doesn’t add anything to your cost, but I do earn a small commission on everything you buy. 

    Thursday, April 26, 2018

    Let's Check Those Tires Again!

     While some of us are still digging out of the winter storms, some of us are dreaming about the first warm weekend of the new camping year. So what do you do first with your stored RV?  Check the tire pressure with a good tire pressure gage.  The tire's max pressure is located on the side wall of the tires on your RV.  Do not use the pressures recommended by the RV manufacture UNLESS the RV has the original tires that it came with from the factory.






    I use both a screw-on tire pressure indicator, such as Quick-Pressure-PSI-50-Monitor, which at a glance can tell you that you may have a problem [use only if your tires are supposed to have 50 lbs of air when cold. Other pressures are available]  and the traditional pencil like gauge, such as Pencil-Pressure Gauge
     Be sure to test or look at the tire pressure gage before you have moved your RV a mile.

    You need to check the tire pressure when the tire is still cold
    Another good, but pricey, system for monitoring your tire pressure as well as the tire temperature is the  Wireless Tire Pressure Monitoring System. I am saving for this one.

    Wireless Tire Pressure Monitoring System

    The system will tell you of an overheated tire, in most cases before it blows, and of course tell you of low pressure in any monitored tire, even the spare,  in real time no need to stop every 20 miles and check those darn tires - LOL.  When you stop for gas or a bathroom break you should do a tire check of the RV as well as a tow vehicle. My daughter was checking the tow vehicle for me and found a large cut in the sidewall of the truck tire.  We were able to get the tire replaced before the large accident occurred.  I did not even remember hitting or running over anything on the highway.
    Be sure to carefully look at the tread, and the side walls both on the front and the back of the tire.  Most RV tire experts agree that if your tiers are more than five years old from the date of manufacture you should replace them.  Most tire failures occur when the side wall of the tire is under inflated or rots out from the inside where you can not see.  You can thank Mr. Sun for sidewall failure in some cases.  Most tires have a Sun inhibitor built-in but when a tire sits and sits the inhibitor does not get moved to the outside of the tire by the tire going round and round.

    Now you see why you need wheel covers right? Trailer Wheel Covers for less than $25.  To protect the tires in storage from Mr. Sun and any other nasties that come along.
    You can also use an RV tire protective spray which is applied, as directed, to the tire sidewall that is exposed to the sun.  I have used RV Tire Protection Spray with good luck.  This spray is NOT designed to make the tire sidewall shinier, it is not a decorative spray, but something that is designed to put back into the surface of the rubber what Mr. Sun is taking out.
    RV Tire Protection Spray
    Also, note that if you are going to store the RV for an extended period of time you should protect the tread from the surface that the tires are sitting on.  Nasty things can leach out of your tires into the blacktop or concrete that your RV sits on while being stored. Or from the blacktop or concrete into your tires during storage.  You can use an  Office Chair Mat that sells for less than $20,
    for each side of the RV and just back onto it as you are putting the RV away.
    Or you can Go to Tractor Supply or any farm supply and pick up horse stall mats

    Cut to the size you need for just $20.  Now that is easy.

    If you are supposed to replace your tires every five years how do you know when your tires were made?  There is a code date molded into the side wall of the tire. (you can thank our government)   The National Highway Traffic Safety Administration (NHTSA) requires that Tire Identification Numbers be a combination of the letters DOT, followed by ten, eleven or twelve letters and/or numbers that identify the manufacturing location, tire size, and manufacturer's code, along with the week and year the tire was manufactured.  Since 2000, the week and year the tire was produced has been provided by the last four digits of the Tire Identification Number with the 2 digits being used to identify the week immediately preceding the 2 digits used to identify the year.

    Below is an example of a tire manufactured since 2000 with the current Tire Identification Number format:

    In the example above DOT U2LL LMLR 5107
    DOT U2LL LMLR 5107 Manufactured during the 51st week of the year
    DOT U2LL LMLR 5107Manufactured during 2007
    While the entire Tire Identification Number is required to be molded onto one sidewall of every tire, current regulations also require that DOT and the first digits of the Tire Identification Number must also be molded onto the opposite sidewall. Therefore, it is possible to see a Tire Identification Number that appears incomplete and requires looking at the tire’s other sidewall to find the entire Tire Identification Number.
    I know you are saying to yourself,  but the RV is only three years old.  We are not talking about the year your RV was built, but the year the tires were manufactured and they may be not the same so please check.   If your tire's serial number cannot be read by you, then you need to take the tire or RV to an RV dealer or tire shop and have the tires read.  Please do not be pulling your RV with old tires that may jeopardize your families safety as well as others.   [If you want more information on tire markings and such go to Tire Tech Information]

    Ok, you have checked the date code of your tires and they are in fact only three years old.  Tire pressure is up and you're ready to go.  Not so fast!

    We need to discuss lug nut tightness.  Each Spring or before a major trip you should check the tightness of the lug nuts on each of the RV tires.  You need to check your owners manual for the correct setting.  My 5er has the specifications of 100ft LBS.  I use an inexpensive torque wrench, which I keep in the RV toolbox, to confirm the setting. 1/2' Torque Wrench  To keep the wrench outside of the tire rim I also use an extender. 1/2" Socket Extension The socket size depends on your lug nut size.

    Tire Check Quick Guide 
    1. Check all RV tires for max pressure listed on the tire sidewall.
    2. Check tire tread and sidewalls for wear and cracks.
    3. Cover tires from sun damage when not using.
    4. Keep tires off of storage surface during storage.
    5. Check the age of tires yearly.
    6. Check your tires every time you stop.
    7. Do maintenance on your tires as needed.
    8. Check lug nut tightness.










    Until Next time.


                                                                           

    Tuesday, April 10, 2018

    What Are Those 12 Volt Sockets Good For?

    We have all done it.  Left the cell phone charger sitting on the kitchen table closed the front door, made sure everything was locked up and left for our weekend RVing get away.  If you have one of those not very smartphones you know that in 8hrs or less the phone will be dead and your Hot Spot, Weather App, and every game that keeps the kids quiet during the ride will come to an end.







    What to do?  Have you ever wondered what the 12 Volt Standard Wall Plate that looks like this is used for?
    2 Volt Standard Wall Plate 
    Or maybe you will remember this 12 volt Wall Plate with Antenna Amplifier & Switch it looks like this;
    12 volt Wall Plate with Antenna Amplifier & Switch
    Both of these wall plates have a 12-volt power socket just like your car, truck, or RV does.  You could plug a car charger for your phone or tablet computer into the wall plate and it would start to charge your phone or tablet computer.  Ah, but you say you have a charger for your phone already why would you need another one for the Rig?  If you remember you left it on the kitchen table and left for this trip.  OK, now what?  Well if you bought one of these 12 Volt Single Outlet USB Charger which looks like this;
    12 Volt Single Outlet USB Charger

    Then all you would need is either the Apple Charging Cable which looks like this;

    or the Android charging cable which looks like this;
    Android charging cable

    and you could charge your phone, table, or any USB device and never have to worry.   You say that you need to charge two USB powered devices at the same time.  Don't worry be happy and buy a Dual USB Charger which looks like this;
     Dual USB Charger
    Now all you have to do is plug in the appropriate charging cable and you are good to go.  If you need longer charging cables than 6ft you can get them up to 10ft for both Apple products and Android products.  If you would like to be able to plug the charging cable into a normal wall outlet you can buy those also.  And for those of us that want it all you can buy the USB Charging Kit Bundle  The one shown below is for Android but they have them for Apple as well.
    USB Charging Kit Bundle
    But they have the Apple Charging Kit Bundle as well, which is shown below;
    Charging Kit Bundle
    Well, that should get you going and you can just plan on leaving any of the items we talked about in the Rig for the next time you leave the charging cable and power supply on the kitchen table.


    PLEASE NOTE:  The following comments may not apply to all RVs.  Without checking the wire gauge behind the socket plate there is no way to be sure that the following products can be hooked up to the 12-volt socket in your RV.

    Along with the ideas above, you can use the power plug to power small appliances such as a coffee maker
    12-volt coffee maker

    or maybe a 12-volt frying pan.
    12-volt frying pan


    Maybe you are boondocking and would like to use your PS3, or some other video game or even some device that only runs on AC.  Then you would use a DC to AC converter.


    This would allow you to power Dual USB ports that can charge most phones and tablets simultaneously (Max 4.8A total output), while two grounded AC outlets (300-350W) great for charging a laptop, breast pump, nebulizer, game console, kindle, TV, DVD players, lights, iPad, and other electronic devices.

    The idea here is that if the park AC power fails you can use the 12 battery that powers your rigs lights, to make coffee while you wait for the power to be restored.  While you are refueling next time at a truck stop go inside a look at all the 12-volt appliance available to the trucking community that you can use in your RV or towing vehicle. [NOTE, not all 12-volt wiring can handle 12-volt appliances.]

    CAUTION:  This is not a long-term solution for power outages as your rig's battery will run down very quickly if you make dinner this way with no way to recharge your RV onboard battery now that the AC power is out.











    Until next time.


    And finally, please remember that this blog is an Amazon affiliate. When you order something through any of the Amazon links, it doesn’t add anything to your cost, but I do earn a small commission on everything you buy.